Ошибка при загрузке модели

Добрый день. Столкнулся с проблемой при загрузке модели.

Последовательность работы при которой была следующей получена ошибка следующая:

1) На суперкомпьютере скомпилировал UDF запустил на расчёт

2) Полученные результаты скопировал на персональный и начал открывать, предварительно скомпилировав UDF

3) После нажатия на открытие *.cas и *.dat следует:

Multicore SMT processors detected. Processor affinity set!

1. Reading "\"| gunzip -c \"D:\2Work\Ivan\result\LES_0.6mln_comb_result_4000ts.cas.gz\"\""...
2. Buffering for file scan...
3.   609616 hexahedral cells, zone  3, binary.
4. Warning: reading 32 partition grid onto 4 compute node machine.
5.          Combining every 8 partitions.
6.   609616 cell partition ids, zone  3, 4 partitions, binary.
7.  1804186 quadrilateral interior faces, zone  2, binary.
8.    27628 quadrilateral wall faces, zone  1, binary.
9.     1624 quadrilateral wall faces, zone  8, binary.
10.     1624 quadrilateral wall faces, zone  9, binary.
11.     4912 quadrilateral wall faces, zone 10, binary.
12.     4912 quadrilateral wall faces, zone 11, binary.
13.     5376 quadrilateral pressure-outlet faces, zone  7, binary.
14.     3248 quadrilateral velocity-inlet faces, zone  6, binary.
15.   634589 nodes, binary.
16.   634589 node flags, binary.
17.    20000 "inlet" point-profile points, x, y, z, x-velocity, y-velocity, z-velocity, turb-kinetic-energy, turb-diss-rate.
18. Checking the existence of compiled "libudf" UDF library for current platform.
19. If needed will attempt auto-compilation...
20. Could not find input files. Found "libudf" library, loading it...
21. Opening library "D:\2Work\Ivan\result\libudf"...
22. Library "D:\2Work\Ivan\result\libudf\win64\3ddp_host\libudf.dll" opened
23. Opening library "D:\2Work\Ivan\result\libudf"...
24. Library "D:\2Work\Ivan\result\libudf\win64\3ddp_node\libudf.dll" opened
25. Opening library "D:\2Work\Ivan\result\libudf"...
26. Library "D:\2Work\Ivan\result\libudf\win64\3ddp_node\libudf.dll" opened
27. Opening library "D:\2Work\Ivan\result\libudf"...
28. Library "D:\2Work\Ivan\result\libudf\win64\3ddp_node\libudf.dll" opened
29. Opening library "D:\2Work\Ivan\result\libudf"...
30. Library "D:\2Work\Ivan\result\libudf\win64\3ddp_node\libudf.dll" opened
31.     user_LaminarFlameSpeed
32.     user_Critical_Strain_Rate
33.     user_Viscosity
34. Done.
35.  
36. WARNING: The current turbulence model should only be used with
37. Second Order (or Bounded Second Order) Transient Formulation.
38. To correct this, use the '/define/models/unsteady-2nd-order?'
39. TUI command or change the Transient Formulation setting in
40. the 'Solution Methods' GUI Task Page.
41.  
42. Building...
43.      mesh
44.     distributing mesh
45.         parts....,
46.         faces....,
47.         nodes....,
48.         cells....,
49.  Warning: Number of nodes read (634589) does not match number referenced (634524).
50.  Performing relabeling.
51.      materials,
52.      interface,
53.      domains,
54.     mixture
55.      zones,
56.     wall_side2
57.     wall_side1
58.     wall_second
59.     wall_first
60.     outlet
61.     inlet
62.     interior-bluffbody-solid
63.     wall-bluffbody-solid
64.     bluffbody-solid
65.      parallel,
66. Opening D:\PROGRA~1\ANSYSI~1\v160\fluent\fluent16.0.0\KINetics\win64\kinetics_usrdll.dll
67. Opening D:\PROGRA~1\ANSYSI~1\v160\fluent\fluent16.0.0\KINetics\win64\KINeticsdll.dll
68. NOTE: Run speed may improve if you re-import CHEMKIN Mechanism
69. Reading "\"| gunzip -c \"RANS_0.6mln_comb.pdf.gz\"\""...
70.     Version of the file: "fluent15.0" 
71.   Read PDF case variables
72.     Type of the PDF Table: Nonadiabatic Table with FGM Model (Two Streams) 
73.   Read species data
74.   Read stream inlets
75.   Read PDF tables
76.     - mixture fraction table
77.     - temperature table
78.     - density table
79.       reading species 20 of  20
80.     - species mole fraction table
81.   Read intermediate data
82. Read 20 species (sectioned c, 3D prepdf)
83. PDF file successfully read.
84. Warning: file C:\Users\Anton1\Desktop\Sl\WS4_17.0\grimech30_thermo.dat does not exist.
85. Error at host: 
86. Unknown independent variable for polynomial
87. Error at Node 0: 
88. Unknown independent variable for polynomial
89. Error at Node 1: 
90. Unknown independent variable for polynomial
91. Error at Node 2: 
92. Unknown independent variable for polynomial
93. Error at Node 3: 
94. Unknown independent variable for polynomial
95. Error: 
96. Unknown independent variable for polynomial
97. Error Object: #f

Подскажите пожалуйста из-за чего происходит эта ошибка. Что делаю не так.